Universal Grounding Kit – You Might Have Pondered Why You Will Be Needing This..

Grounding exterior cables is just as important as selecting the best cables for your television or Internet system. Grounding can prevent shocks from lightning strikes and surges from shooting across your coaxial cable and into the back of your television or Internet system. It’s also not very complicated: anyone capable of connecting 1/2” Foam Cable can ground that very same cable to an existing electrical ground with little trouble.

Any television system with wires that run outdoors should ground them. Attach the grounding block to your house, somewhere near to in which the coaxial cable comes in. A grounding block could have at least two screw holes; drill holes for every, then secure the block to the wall with all the included screws.

Disconnect the coaxial cable through the splitter and hook it up to a single side in the grounding block. You can do this simply by twisting the end until it will come loose. Lightly coat the ports on the grounding block using the silicone grease. This can assist in weatherproofing the ports. Carry out the same for virtually any open ports on the coaxial splitter.

Connect a new RG-6 coaxial cable to the level on the splitter where the previous cable was disconnected. Then attach one other end in the cable to the other part from the grounding block. Coaxial cables attach by inserting the pin from the middle of the cable in to the pin-sized hole on the port, then twisting the cable until it secures in place.

Attach the grounding wire for the grounding screw on the grounding block. Loop the wire across the screw and twist the screw in till the wire is secure. Then run the wire for the electrical ground and attach the wire there in the same manner. If no screw is available, twist the conclusion in the cable around the ground as tightly as is possible; crimping with pliers if needed.

Before I recieve into how and why you ought to ground your antenna, I wanted to let you know I am not an electrician. I’m a DIY weekend warrior that relies upon Google search-fu to discover ways to do household repairs and installs.

For just about any engineers or electricians that drop by, I welcome any critiques or corrections within the comments. Accuracy is very important in my opinion, and i also appreciate any corrections or adjustments you can offer.

That said, numerous years of working in enterprise architecture make me somewhat of a stickler for standards and practices. If you are also, you might like to check out Article 810 from the National Electric Code. It covers each of the codes and standards for installing the cabling for TV and radio transmitters.

However, if you are like many people, you’d rather hit your thumb repeatedly having a hammer than suffer through technical manuals. If so, I’ll do my best to walk you through what I did after looking over the code.

Below is really a picture describing precisely what we are going to do. It illustrates the best way to ground your antenna by connecting it to your house’s ground wire. Notice you must not only ground the Universal Grounding Kit, however the antenna mast too.

Grounding an antenna isn’t difficult to accomplish yourself, however it shouldn’t be too expensive to get a professional emerge and do that for you personally. In order to attempt this, here are would be the steps I took to recreate precisely what is essentially depicted in the diagram.

Cable installation basics. Install equipment and cabling in a neat and workmanlike manner [820.24]. You will find the industry practices described in ANSI/NECA/BICSI 568, Standard for Installing Commercial Building Telecommunications Cabling.

Exposed cables has to be maintained by the structural components of the building to stop cable damage due to normal building use. Secure cables with straps, staples, hangers, or similar fittings designed and fmpuqh in order never to damage the cable.

Cables run parallel to framing members or furring strips should be protected where they are likely to be penetrated by nails or screws. To provide this protection, you may have two options. Install the cables at least 1¼ inches from the nearest side of the framing member or furring strips.

Protect the Coax Cable Clamp using a 1/16-inch-thick steel plate Wiring support rules for coaxial cables could be a little tricky. Ensure you know when and where independent support wires should be used. You must securely fasten raceways that have coaxial cables in position. Don’t use ceiling-support wires or even the ceiling grid to back up raceways or cables. You can, however, support raceways and cables with independent support wires attached to the suspended ceiling.

Leave a Reply

Your email address will not be published. Required fields are marked *